NTI, st-ipfo4k18gb-r-lc, 4K 18Gbps HDMI Extender Over IP via One LC Fiber Optic Cable, Receiver Only
st-ipfo4k18gb-lc Includes Only:
- One transmitter unit
- One receiver unit
- One T1270/R1330nm 10G Base-T SFP module
- One T1330/R1270nm 10G Base-T SFP module
- One IR emitter
- One IR receiver
- Two power supplies
- Mounting brackets
Features:
- Signal transmission via single-strand LC fiber optic cable.
- Using singlemode 9-micron cable, extend to 24.8 miles (40 km).
- Using 50-micron OM2 (or better) multimode cable, extend to 1,640 feet (500 meters).
- Zero latency.
- Supports Ultra-HD 4Kx2K resolutions to 3840x2160 and 4096x2160 at60Hz YUV 4:4:4, HDTV resolutions to 1080p at60Hz, and up to 1920x1200 (WUXGA).
- Cascade network switches to extend the length longer distances.
- Up to 12 switches can be cascaded.
- HDMI features supported:
- HDMI 2.0
- 8-bit, 10-bit, and 12-bit Deep Color
- Dolby TrueHD, DTS-HD Master Audio, Dolby Digital, Dolby Digital+, Dolby Atmos, LPCM 7.1CH, DTS 5.1, and DTS:X
- RGB, YCbCr 4:4:4, YCbCr 4:2:2, and YCbCr 4:2:0/li>
- Bandwidth up to 600 Mhz (18Gbps)
- 3D (1080p at60Hz)
- Support for CEC (consumer electronic control) compatible devices.
- HDR10
- ARC
- HDCP 2.2 and 1.4 compliant.
- Supports local and remote HDMI displays.
- For a point-to-many connection, a standalone network with an unmanaged 10G SFP network switch, hub, or router can be used instead of a managed SFP network switch.
- Easily expandable. Add remote units as you add monitors.
- Up to 255 receivers supported.
- It is not recommended to use any other network devices on this standalone network as it may cause degradation in performance.
- Support for multiple transmitters (many-to-many connection) requires a managed 10G SFP network switch with IGMP support and Jumbo frame support. Standard LAN switches can only support one transmitter.
- The managed 10G SFP network switch must support port-based IEEE 802.1Q VLAN.
- Each VLAN acts as a separate HDMI Over IP Channel on the network.
- Each VLAN channel supports one transmitter.
- The number of local and remote units that can be used is dependent on the backplane bandwidth of the switch.
- Plug and play installation allows receivers to find the transmitters automatically on the same subnet.
- Local and remote units must be in the same LAN. The units do not support WAN connections.
- Built-in default EDID table.
- Supports full-duplex RS232 up to 115200 baud.
- Bi-directional IR control from input and output locations.
- Supports HDMI embedded digital audio and ARC audio extraction via Toslink connection.
- Built-in surge and ESD protection.
- Mounting brackets included for easy surface/wall mounting.
The XTENDEX® 4K 18Gbps HDMI Extender Over IP via Fiber Optic Cable locates an Ultra-HD 4Kx2K 60Hz 4:4:4 HDMI display, audio, IR, and RS232 up to 24.8 miles (40 kilometers) away from an HDMI source using a single LC singlemode fiber optic strand or 1,640 feet (500 meters) using LC multimode fiber optic cable.
Each 4K 18Gbps HDMI Extender Over IP consists of a local unit that connects to an HDMI source and a local display via the HDMI loop output, and a remote unit that connects to an HDMI display. The local and remote units can be connected together for a Point-to-Point connection via Fiber Optic Cable or a Point-to-Many connection via a 10G SFP network switch. Support for multiple transmitters requires a managed 10G SFP network switch.
