| Product Characteristics |
| Number of Inputs and Outputs | Number of Digital Outputs: 2Number of Analog Outputs: 1 |
| Measuring range [MPa] | 0 - 25 |
| Process Connection | Homogenizer connection |
| System | Gold-plated contacts |
| Measuring Element | Diaphragm seal |
| Media | Liquids and gases |
| Medium Temperature [° C] | 5 - 90; (for further details see section Diagrams and graphs) |
| Min. bursting pressure [MPa] | 100 |
| Pressure Rating [MPa] | 50 |
| Vacuum Resistance [mbar] | -1000 |
| Type of Pressure | Relative pressure |
| Electrical Data |
| Operating Voltage [V] | 18 - 30 DC; (to SELV/PELV) |
| Current Consumption [mA] | < 35 |
| Minimum Insulation Resistance [MΩ ] | 100; (500 V DC) |
| Protection Class | III |
| Reverse Polarity Protection | Yes |
| Power-on Delay Time [s] | 0.3 |
| Integrated Watchdog | Yes |
| Inputs / Outputs |
| Number of Inputs and Outputs | Number of Digital Outputs: 2Number of Analog Outputs: 1 |
| Outputs |
| Total Number of Outputs | 2 |
| Output Signal | Switching signal; analog signal; IO-Link; (configurable) |
| Electrical Design | PNP/NPN |
| Number of Digital Outputs | 2 |
| Output Function | Normally open / closed; (configurable) |
| Maximum Voltage Drop Switching Output DC [V] | 2 |
| Permanent Current Rating of Switching Output DC [mA] | 250 |
| Switching Frequency DC [Hz] | < 500 |
| Number of Analog Outputs | 1 |
| Analog Current Output [mA] | 4 - 20; (scalable 1: 5) |
| Maximum Load [Ω ] | 500 |
| Analog Voltage Output [V] | 0 - 10; (scalable 1: 5) |
| Minimum Load Resistance [Ω ] | 2000 |
| Short-Circuit Protection | Yes |
| Type of Short-Circuit Protection | Yes (non-latching) |
| Overload Protection | Yes |
| Measuring/Setting Range |
| Measuring range [MPa] | 0 - 25 |
| Set point SP [MPa] | 0.15 - 25 |
| Reset point rP [MPa] | 0.05 - 24.9 |
| Analog start point [MPa] | 0 - 20 |
| Analog end point [MPa] | 5 - 25 |
| In steps of [MPa] | 0.05 |
| Accuracy / Deviations |
| Switch Point Accuracy [% of the Span] | < ± 0,4; (Turn down 1: 1) |
| Repeatability [% of the Span] | < ± 0,1; (with temperature fluctuations<10 K; Turn down 1: 1) |
| Characteristics Deviation [% of the Span] | < ± 1; (linearity, incl. hysteresis and repeatability; limit value setting to DIN EN IEC 62828-1) |
| Hysteresis Deviation [% of the Span] | < ± 0,1; (Turn down 1: 1) |
| Long-Term Stability [% of the Span] | < ± 0,05; (Turn down 1: 1; per 6 months) |
| Temperature coefficient Zero Point [% of the Span / 10 K] | 0,2; (5 - 80 ° C) |
| Temperature Coefficient Span [% of the Span / 10 K] | 0,2; (5 - 80 ° C) |
| Reaction Times |
| Response Time [ms] | < 1.5 |
| Delay Time Programmable dS, dr [s] | 0 - 50 |
| Damping Process Value dAP [s] | 0 - 4 |
| Damping for the Analog Output dAA [s] | 0 - 4 |
| Maximum Response Time Analog Output [ms] | 3 |
| Software / Programming |
| Parameter Setting | Hysteresis / window; normally open / closed; switch-on/switch-off delay; Damping; Display Unit; current/voltage output |
| Interfaces |
| Communication Interface | IO-Link |
| Transmission Type | COM2 (38,4 kBaud) |
| IO-Link Revision | 1.1 |
| SDCI Standard | IEC 61131-9 |
| Profiles | Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis |
| SIO Mode | Yes |
| Required Master Port Class | A |
| Process Data Analog | 1 |
| Process Data Binary | 2 |
| Minimum Process Cycle Time [ms] | 2.3 |
| Operating Conditions |
| Ambient Temperature [° C] | 5 - 80 |
| Storage Temperature [° C] | -40 - 100 |
| Protection | IP 67 |
| MTTF [Years] | 143 |
| Mechanical Data |
| Weight [g] | 675 |
| Material | 1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); stainless steel (1.4435 / 316L); PBT+PC-GF30; PBT-GF20; PC |
| Materials (Wetted Parts) | Stainless steel (1.4435 / 316L) |
| Minimum Pressure Cycles | 60 million; (at 1.2 times nominal pressure) |
| Process Connection | Homogenizer connection |
