| Control 1 Output Specifications |
| Contact Rating (SPST | 5a at 230VAC / 30VDC resistive |
| SSR Drive (Voltage Pulse) | 18VDC 20ma |
| Current | 0/4 to 20ma dc (loop impedence 500 ohms max |
| Voltage | 0 to 5/10 VDC (load resistance 10K ohms min) |
| Alarm 2 Output Specification |
| Contact Rating (SPST) | 5a at 230VAC / 30VDC resistive |
| SSR DRIVE | 12VDC 20ma |
| Functional Specification |
| Control Action | PID, On-Of |
| Proportional Band (P) | 0.0 to 400.0 deg |
| Integral Time (I) | 0 to 3600 sec |
| Derivative Time (D) | 0 to 200 sec |
| Cycle Time | 0.1 to 100.0 sec |
| Hysteresis Width | 0.1 to 99.9 deg |
| Manual Reset Value | 99.9 to 99.9 deg |
| Heat Cool Pid |
| Control Action | PID |
| Cycle Time | 0.1 to 100 sec |
| Proportional Gain | 0.0 to 400.0 deg |
| Deadband | Programmable from setpoint low limit to setpoint high limit |
| Alarms |
| Modes | Deviation high/low, Absolute high/low, band, sensor break |
| Hysterisis | 0.1 to 99.9 deg |
| Ramp Soak |
| Ramp Rage | 1 to 9999 deg/hr. |
| Soak Time | 0 to 1440 min |
| Soft Start Time | 0 to 999 min |
| Supply Voltage | 85 to 270V AC/DC (50/60 Hz) |
| Power Consumption | 6VA max at 230 VAC |
| Retransmission |
| Current | 0/4 to 20ma DC (loop impedence 500 ohms max) |
| Voltage | 0 to 5/10V DC (load resistance 10k ohms min) |
| Update Rate | 100msec |
| Serial Communication |
| Interface Standard | RS485 |
| Communication Address | 1 to 99, maximum of 32 units per line |
| Transmission mode | Half duplex |
| Transmission protocol | MODBUS RTU |
| Transmission distance | 500 m maximum |
| Transmission speed | 9600, 4800, 1200, 600, 300 bits/sec. |
| Temperature |
| Operating | 0 to 50°C (32 to 122°F) |
| Storage | -20 to 75°C (-4 to 167°F) |
| Humidity (Non Condensing) | 95% RH |
| Weight | 6.4 oz |
| Protection Level | IP65 for faceplate |
| Digits | - 4 digit, 7 segment LED Dual Display
- Height of Upper display: 0.3785"
- Height of Lower display: 0.2720"
|
| Led indications | Relay On, Alarm, Manual Mode, Tune |
| Inputs | - Thermocouple (J,K,T,R,S,C,E,B,N,L,U,W)
- Platinel II, RTD (Pt100)
- DC Analog Inputs (-5 to 56mv, 0 to 10v, 0 to 20 ma)
|
| Sampling Time | 200 ms |
| Input Filter (FTC) | 0.2 to 10.0 sec |
| Resolution | - 1/0.1 deg for TC/RTD only
- Fixed 1 deg resolution for R&S Type TC)
- Decimal point position selectable: 1/0.1/0.01/0.001 for analog input
|
| Temperature Unit | C/F deg selectable |
| Indication ACC: | - For TC inputs 0.25% of F.S. ± 1°
- R&S type TC inputs 0.5% of F.S. ± 2 deg (20 min of warm up time for TC inputs)
- For RTD inputs 0.1% of F.S. ± 1 deg
- For Analog Input ± 0.5%, ± 1 digit
|
