| Video |
| Digital Video Input | HDMI 2.0, DVI-D* (through adapter), Dual-Mode DisplayPort (DP++) |
| Analog Video Input | HD-15 VGA |
| Video Output | Network video over Ethernet via RJ45 port or SFP via 1G SFP+ port, HDMI, DVI-D |
| Formats | - HDMI 2.0, DVI-D (through adapter), Dual-Mode DisplayPort (DP++), HDCP 2.2 content protection support, RGBHV
- DVI-D and Dual-Mode DisplayPort (DP++) are supported through a passive adapter
|
| Progressive Input Resolutions | - Supports 4K30 4:2:0 and most common HD resolutions up to 1920x1200
- See NMX-ENC-N2312 Installation Manual for all supported resolutions
- HDMI and DVI (Progressive)
- Pixel clock between 27 MHz – 300MHz
- Minimum resolution of 720x480p60
- Maximum horizontal resolution of 4096 or a vertical resolution of 2160
|
| Common acceptable resolutions include | 720x480p60 – 480p, 720x576 at 50, 800x600p60, 1024x768p60, 1280x720 at 60Hz - 720p60, 1600x1200 at 60Hz, 1920x1080 at 60Hz - 1080p60, 3840x2160(4:2:0) at 30Hz - UHD30 aka 4K30, 4096x2160(4:2:0) at 30Hz - DCI 4K30 |
| Interlaced Input Resolutions | - Supports 1080i60
- See NMX-ENC-N2312 Installation Manual for all supported resoltuions
- HDMI and DVI (Interlaced)
- 1920x1080 at 50Hz - 1080i50
- 1920x1080 at 60Hz - 1080i60
|
| Analog Input Resolutions | - Supports most common HD resolutions up to 1920x1200
- See NMX-ENC-N2312 Installation Manual for all supported resoltuions
- VGA
- Pixel clock between 27 MHz - 165 MHz
- Minimum resolution of 640x480
- Maximum horizontal resolution of 1920 or a vertical resolution of 1200
- Common acceptable resolutions include: 640x480p60, 720x480p60 – 480p, 720x576 at 50,800x600p60, 1024x768 at 60Hz, 1280x720 at 50Hz (720p50), 1280x720 at 60Hz (720p60), 1280x768 at 60Hz, 1280x800 at 60Hz, 1280x960 at 60Hz, 1280x1024 at 60Hz, 1360x768 at 60Hz, 1366x768 at 60Hz, 1400x1050 at 60Hz, 1440x900 at 60Hz, 1600x1200 at 60Hz, 1680x1050 at 60Hz, 1920x1080 at 50Hz (1080p50), 1920x1080 at 60Hz (1080p60), 1920x1200 at 60Hz (reduced blanking)
- Analog-To-Digital Conversion: 8-bit 165 MHz per each of three color channels
- Color Space: 4:2:0 4K30, 4:2:2 – HD
- LocalPlay/HostPlay: 8 playlists
- HostPlay: 1 image/list
- Note: Jumbo Frames Required
- Video Wall Construction: Supported within the NMX-DEC-N2322, the N2300 Series is not compatible with SVSI Windowing Processors at this time
- Network Video Recording: Not compatible with SVSI NVR at this time
|
| Audio |
| Input Signal Types | Embedded audio on HDMI (DVI-D through adapter) or Analog Stereo (Balanced or Unbalanced) |
| Output Signal Types | Ethernet, Embedded audio on HDMI or DVI-D (through adapter) |
| HDMI Audio Formats | 8ch PCM |
| Analog Audio Format | Stereo 2-channel |
| Analog-To-Digital Conversion | 48 kHz |
| Keyboard and Mouse | Connect the Decoder to the keyboard and mouse, and an N2300 Series Encoder to the PC being controlled |
| Latency |
| Latency | - 17-ms at 60 fps for 1920x1080 and lower resolutions
- 34-ms at 30 fps for 4K30
|
| Switching | Up to 1.5s delay, not seamless |
| Bandwidth |
| Bandwidth | Approximately 160 Mb/s |
| Communications |
| Ethernet |
| P0 | 10/100/1000 Mbps, auto-negotiating, auto-sensing, PoE,full/half duplex, DHCP, Auto IP, and Static IP |
| P1 | 1 Gbps port which accepts compatible fiber transceivers or direct attach cables, DHCP, Auto IP, and static IP |
| HDMI | HDCP, EDID Management |
| PORTS |
| +12V 2A | One 12 Volt DC power input |
| P0 | - 8-wire RJ45 female
- 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port with PoE
- Provides network connection and power to the Encoders and Decoders
|
| P1 | - 1-Gbps SFP+ port (SFP+ fiber transceiver or direct attach cable not included)
- Provides network connection and networked AV video
|
| IR IN (front panel) | 3-pin terminal Phoenix connector. Provides Infrared (IR) input only and passes signal back to connected decoder (33-60 kHz; typically 39 kHz) IR receiver is necessary (not included) |
| IR OUT | - 2-pin terminal Phoenix connector
- Provides Infrared (IR) output only (33-60 kHz; typically 39 kHz). Emitter is necessary (not included)
|
| RS232 | - 3-pin terminal Phoenix connector which provides a serial control interface. Full duplex communication.
- Available terminal speed settings: 1200-115200 baud rate
|
| Audio | - 5-pin terminal Phoenix connector which provides userselectable balanced/unbalanced input
- Dedicated audio input
|
| HDMI OUT | HDMI video output (passive pass-through from HDMI IN) |
| HDMI IN | HDMI video input |
| VGA IN | DB15 analog input |
| Controls and indicators – front panel |
| Reset button | - Recessed pushbutton
- Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings.
|
| ID button | - Recessed pushbutton
- Press to send a notification out on the network to identify the unit (the notification causes a pop-up dialog in N-Able and N-Command)
|
| Power LED | - On solid (green) when operating power is supplied (via PoE or local power supply).
- This activity is also shown by the PWR LED on the rear panel
|
| Status LED | - On flashing (green) when there is software activity.
- This activity is also shown by the STAT LED on the rear panel.
|
| Controls and Indicators – Rear Panel |
| PWR LED | Same as POWER LED described above. |
| HDMI LED | On (green) when there is a connection to a valid video source |
| STAT LED | Same as STATUS LED described above. |
| STRM LED | On (green) when the unit is streaming video. |
| Environmental |
| Temperature | 32° to 104°F (0° to 40°C) |
| Humidity | 10% to 90% RH (non-condensing) |
| Heat Dissipation | Up to ~ 44 BTU/Hr |
