| Video |
| Digital Video Input | Network video over Ethernet via RJ45 ports |
| Video Output | HDMI, DVI-D (through adapter) |
| Formats | HDMI, DVI-D (through adapter), HDCP content protectionsupport |
| Output Resolutions | Supports most common HD up to 1920x1200 |
| Audio |
| Input Signal Types | Network video over Ethernet via RJ45 |
| Output Signal Types | - Embedded audio on HDMI or DVI-D (through adapter)
- Ethernet standard SVSI audio stream or AES67 (user selectable)
|
| HDMI Audio Formats | 8ch PCM |
| Analog Audio Format | Stereo 2-channel |
| Digital-to-Analog Conversion | 16-bit 32 kHz, 44.1 kHz and 48 kHz (matched to Encodersettings) |
| Latency |
| Video Latency | 10 ms at 60 fps |
| Audio Latency | Standard SVSi audio stream = 17-msec (synched to video) ;AES67 = <1-msec adjustable to 17-msec |
| Note | - Video and audio latency values are the combined encode plus decode latency. Total latency from source to screen will also include any network latency.
- Scaling adds one frame of latency (17ms at 60fps).
|
| Communications |
| Ethernet |
| P0 | 10/100/1000 Mbps, auto-negotiating, auto-sensing, PoE,full/half duplex, DHCP, Auto IP, and Static IP |
| P1 | 10/100/1000 Mbps, auto-negotiating, auto-sensing,full/half duplex, DHCP, Auto IP, and Static IP |
| HDMI | HDCP, EDID Management |
| PORTS |
| +12V 2A | One 12 Volt DC power input |
| P0 | - 8-wire RJ45 female
- 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port with PoE
- Provides network connection and power to the Encoders and Decoders
|
| P1 | - 8-wire RJ45 female
- 10/100/1000 Mbps 10/100/1000Base-T auto sensing gigabit Ethernet switch port
|
| IR | - 2-pin terminal Phoenix connector
- Provides Infrared (IR) output only (33-60 kHz; typically 39 kHz). Emitter may be necessary (not included)
|
| RS232 | - 3-pin terminal Phoenix connector
- Provides a serial control interface. Full duplex communication. Available terminal speed settings: 1200- 115200 baud rate.
|
| Audio | - 5-pin terminal Phoenix connector
- Provides user-selectable balanced/unbalanced output Dedicated audio output.
|
| HDMI OUT | HDMI video output |
| Controls and indicators – front panel |
| Reset button | - Recessed pushbutton
- Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings.
|
| ID button | - Recessed pushbutton
- Press to send a notification out on the network to identify the unit (the notification causes a pop-up dialog in N-Able and N-Command)
|
| Power LED | - On solid (green) when operating power is supplied (via PoE or local power supply).
- This activity is also shown by the PWR LED on the rear panel
|
| Status LED | - On flashing (green) when there is software activity.
- This activity is also shown by the STAT LED on the rear panel.
|
| Controls and Indicators – Rear Panel |
| PWR LED | Same as POWER LED described above. |
| HDMI LED | On (green) when there is a connection to a valid video source |
| STAT LED | Same as STATUS LED described above. |
| STRM LED | On (green) when the unit is streaming video. |
| Environmental |
| Temperature | 32° to 104°F (0° to 40°C) |
| Humidity | 10% to 90% RH (non-condensing) |
| Heat Dissipation | Up to ~ 44 BTU/Hr |
| General |
| Dimensions (HWD) | 1.05” x 7.888” x 5” (2.67 cm x 20.04 cm x 12.7 cm) |
| Weight | 1.47 lbs (0.67 kg) |
| Regulatory Compliance | FCC, CE, and NRTL |
