Balanced vs Unbalanced Audio Cables

Cables that are used in the audio systems may have a significant impact on the sound of the system. Each cable in the audio system has the aspect to add noise and to compromise the sound quality of the components that are connected with it. That is why it is significant to choose the proper cable for the correct job. The proper job begins with understanding the types of signals that are carried by the cables.

There are two major tasks to find out: The level of the signal and types of the signals. You’ll find out about balanced and unbalanced types of signals below.

What are Unbalanced Cables and Signals

Unbalanced cables have two connectors with two conductors on each that are fixed by two wires (signal and ground wires) inside the cable. In most cases, you may fastly determine a cable designed to carry unbalanced signals by the connectors, because each wire has to be completed at the connector with its own contact endpoint. Unbalanced cables should have only two conductors at the connector.

The signal wire is generally placed in the center inside the cable with the ground wire that surrounds it. The ground wire has two functions: it transmits part of the audio signal and protects the major signal wire from outside disturbance from noise such as the hum from light or radio frequency interference that is transmitted from TV or radio transmissions. It provides a proper job of preventing noise. However, the wire also works like the antenna itself, unfortunately, and gathers the noise.

*Unbalanced wiring uses only two conductors and is responsive to gathering the noise.

Unbalanced cables work better for connecting the guitar to an amp, for example, but due to they are not good enough at suppressing noise from the outside interference. Unbalanced cables should be of 15-20 feet (4-6 meters), especially when they are used in noisy conditions or with signals that are at a low level to start with, such as signals from the keyboard, guitars, MP3 devices, etc.

What are Balanced Cables and Singnals

Balanced cables, in comparison with the unbalanced, have three conductors that are fixed to the connector and three wires in the cable: two signal wires and a separate ground wire. As you already know, that unbalanced wire surrounds the signal wire and prevents any unbalanced noise. The balanced cable has a specific aspect, that its gear utilizes the extra signal wire.

The balanced XLR cable, which is shown above, demonstrates two signal wires and the separate ground wire with a foil shield in comparison with a common 2-conductor TS guitar cable that is shown below.

The balanced cable uses two signal wires that transmit a duplicate of the signal. However, these two duplicates are sent with their polarity overturned. When you total two signals that are equal, but duplicates are overturned in polarity, the signals invalidate, thus providing you the silence. For instance, it is just like sum positive and negative numbers: +2 added to -2 is equal to 0.

If you add the signal, that is on the left, to a reversed duplicate of itself, that is on the right, the results will be in a invalidate signal, as positive limits on the left signal match to equally negative limits in the reversed signal.

So, why do you prefer audio gear that turns the polarity of the signal? In that case, it is because the accepting gear will turn the reversed signal back into the original signal. However, two duplicates of the signal that gather the same noise as they go along the cable - and this noise is equal to the two wires in the cable- turning the polarity that transmits through the accepting gear, will provide you with pleasant results: the signal that is prevented and the noise that is invalidated.

Balanced wire uses two signal conductors and the separate ground signal, thus letting the noise be gathered through the path to be invalidated through the polarity reversal.

In this case, the balanced cables can bolster much longer cable runs: from 50 to 100 feet (from 15 to 30 meters) is not unusual, thus even shorter runs will use balanced wires to preserve against noise.

Wires that are used for microphones and the interconnect cables that are between the consoles, signal processors, amps, and so on that are used in a pro-sound system and recording studio environment conditions are generally of the balanced range. Common standard connectors are produced for use with balanced signals are XLR and TRS.

Use The Proper Cable For The Proper Signal

It is significant to note that balanced cables that are used on the unbalanced signal won’t give benefits to the work. The jacks on the gear that is on both endpoints of the cable should be produced for the balanced signals as well, or there will be no path to make the polarity reversal that provides the noise invalidation.

On the other side, the use of the unbalanced cable with the gear, that functions with the balanced signals, will provide “work”, that means that the audio will pass from point A to point B. However, the signal will be unbalanced and responsive to the same noise as the other unbalanced signals as well. That is why read the instructions of the gear you get carefully to understand what kind of the signal is of the given jack is made to bolster if you are not sure.